Pushrod holder and next tunings for T-Rex600

Never more of uncomfortable works with original holders. These holder averting deflection of pushrod. Part of this holder is also rod slide ring which makes possible to light driving in different angles of rod. Also we offer new other tunings for T-Rex 600 like is for example mounts of tail boom support for their better function. Also we have prepared tail servo holder for save of weight of electric powered heli. More informations by email or here here


Bracket for tail boom support of 30 & 50 size helis

Ultra light bracket for tail boom support prohibitive of vibrations. Also averting flexion of boom. Necessary is support's boom take over silicon tube. This bracket is possible to use for support's booms to diameter 5mm (max 6mm). More informations by email or here here


Metal servo mounts

After some next our experience with Protos helicopter we would like offer to you next our tuning. It is tail servo mounts. We have developed 3 types for micro(mini), midi and standard servos. Also these holders have mount for antistatics cable which we have also in our offer (no. MT9110). More information here


Metal tail boom support holder
Like next we would like offer to you tail boom support holder, which hold the boom very good. Also we have light pushrod holder. Part of this holder is also rod slide ring which makes possible to light driving in different angles of rod. Also you can compared with original holder give it to center of tail rod. It is better for less vibrations and deflection. You can also give more holders at one rod.

More information here


Metal Antenna Holder
After experiences when users have problems that original short plastic antennna holders for system 2,4GHz and transmitters with ball's antenna holders is very breakable and is not possible to buy that like sparepart, we have made new metal antenna holder which this problem eliminated for ever. This holder is destined for antenna with inside hole of diameter 14mm (14,2mm) and mainly antenna by Spektrum and JR radios (for example JR10X). More informations by email or here


Tail CNC Pulley
Metal but lightweight pulley for MSH Protos. Precision manufacturing of the pulley teeth profiles provides a good transfer of the energy without an unnecessarily tight driving belt. These pulley lowering tail vibrations.

CNC Tensive Pulley
Precision metal tensive pulleys provide very good wiring of belt. It is interesting for lowering vibrations of model and also less belt wear. More informations here





Due to the approaching 2,4GHz technology, the thumb-controlled radio transmitters started to experience problems with unsuitable attachment of the neck-strip which causes an unpleasant shift in the center of gravity. This means that the hanging transmitter has the tendency to tilt towards the pilot's chest and this may result in unwanted manipulation with the control sticks or other switches. As an answer to this problem, we designed a special extension bracket which moves the center of gravity to the correct location and enables a pleasant handling of the transmitter. This bracket is, of course, suitable also for transmitters with the classical antenna, which may also experience similar problems. More informations here





Tail Boom Support set for Duzi R5 Nova

Allows to more gyro gain...

A better Tail and Gyro function...

A better stopping from piruettes...

Like protection of tail boom in crashes...

More informations here





Helicopter Duzi R5 Nova now for sale

Integrated gearboxes with lunricant curcuit,

special construction for 3D extreme flying, ultimate center drive of tail rotor,

all gears from hard-treated steel, figer-glass-carbon color canopy,

controlled by midi-servos, modular system chassis, over 70 ball-bearings,

push-pull linkages, cardan tail shaft

More informations here






A complete tail unit ready for a flight. This all unig has weight 15g. The gearbox is a single and compact alu block of a very massive construction and highly crash resistant. The shaft is very robust and corrosion-free together with a CNC belt pulley and symmetric locking surfaces for fixing the central grip holder. The shaft is attached via three ball-bearings. The output side is equipped with a double ball-bearing house enabling a quick belt change. The pitch slider works extremely smooth due to a plastic delrin tube and links are equipped with micro ball-bearings to ensure the smallest possible slop in the whole system. More informations here